NetApp VSC 4.2.2 HTTP Error 500 VSphereAuthenticationFilter only support jetty requests



NetApp KB ID 2026327 only states error 503, but the fix listed in the article will also fix this error 500 problem too.

It seems to only affect vCenters running 5.5 U3b or higher.  Anyway, probably far and few between dealing w/ this, but hopefully this helps someone looking for a solution.  Long story short, the KB details certain conf files that need to be modified.

Perform the following steps to resolve the issue:
  1. Open %Programfiles%\Netapp\Virtual Storage Console\smvi\server\etc\wrapper.conf
  2. Locate the wrapper.java.additional.X lines (should be 4)
  3. Add the following line:
    wrapper.java.additional.5=-Dhttps.protocols=TLSv1,TLSv1.1,TLSv1.2
  4. Open %Programfiles%\Netapp\Virtual Storage Console\wrapper\wrapper.conf
  5. Locate the wrapper.java.additional.X lines (should be 7)
  6. Add the following additional line:
    wrapper.java.additional.8=-Dhttps.protocols=TLSv1,TLSv1.1,TLSv1.2
  7. Restart both VSC services, or reboot.


Comments

Unknown said…
Thanks! I ran into this and the link to the KB was useful.

I presumed it would be something like this as VMware messed with SSL in 5.5U3, upgrading hosts before vCenter for example means they don't reconnect.
February 23, 2016 at 5:53 PM
Anonymous said…
Legend! Thank You!
April 14, 2016 at 7:46 AM
Ross said…
Works like a dream now. Thanks!
September 2, 2016 at 5:40 AM
Anonymous said…
Worked like a charm !! thanks !
March 28, 2017 at 8:07 AM
Anonymous said…
Just upgraded vCenter from 5.1 to 5.5u3f and this worked perfectly.
October 5, 2017 at 12:45 PM
Anonymous said…
Worked after reboot. Saved my day.Thx!!!!!
December 4, 2017 at 5:52 AM
Anonymous said…
Sup gents please help, where do i add the line beofre .4= or after?
August 2, 2018 at 7:36 AM
Zsoldier said…
I don't think order matters.
September 19, 2018 at 10:47 AM
Post a Comment

Popular posts from this blog

NSX-T: Release associated invalid node ID from certificate

Image
Summary: Basically had an expiring certificate registered in NSX-T that was associated to a node_id that is no longer valid.  Long story short, there wasn't anything obvious in API to delete or disassociate a certificate from a node_id for 3.2.2.  Not sure how things got in this state, but annotating for future reference.  This may change in future revisions, so always check API for latest. Details: Effectively had a stale node associated w/ a certificate that was expiring.  Could not delete certificate until that node was disassociated from the certificate. To get certificate details and associated node_id's, you can use the following curl call (UI works too): curl -k -X GET -H "Content-Type: application/json" -u admin https://<manager ip>/api/v1/trust-management/certificates/<cert UUID> Above will return something like this: Below must be run from one of the manager nodes via elevation to root: ONLY RUN THIS IF YOU ARE ABSOLUTELY SURE OF WHAT YOU ARE DO...
Read more

NSX-T: vCenter and NSX-T Inventory out of Sync (Hosts in vSphere not showing up in NSX-T)

Image
Summary: NSX-T loses synch w/ vCenter inventory, but statuses don't appear to show an issue.  Basically, you add a host to a vCenter cluster, NSX-T bits should start to automatically installing on new host.  Assuming you've created a Transport Node Profile and associated w/ the cluster.  The problem is that NSX-T doesn't see the new host and its link to the compute manager (vCenter) looks fine. Looks fine, Y U NO WORK!? So what's going on here?  This appears to affect NSX-T 2.5 and 2.5.1.  Cause is unknown. Workaround: Restart the cm-inventory service on each NSX-T mgmt/controller node using API or CLI. Details: If you were to query the status of the cm-inventory via API or CLI, you could query all 3 manager/controller nodes and get a status of running.  Even if the primary node associated w/ the VIP, if configured, is not necessarily in charge of inventory.  So you could restart the cm-inventory service till you are blue in the face ...
Read more

MacOS: AnyConnect VPN client was unable to successfully verify the IP forwarding table modifications.

Image
The VPN client was unable to successfully verify the IP forwarding table modification.  A VPN connection will not be established. Summary: I started running into issue utilizing Cisco AnyConnect on my Mac basically complaining about not able to overwrite IP forwarding tables.  This was on 4.6.x.  Since my VPN endpoints were not providing me w/ an updated client and w/ no access to Cisco Anyconnect downloads, my only option was to try openconnect.  It was totally worth it, here is why and how to set it up. PreReqs: Homebrew Installing OpenConnect: Launch MacOS Terminal brew install openconnect Getting VPN IP's/DNS Endpoints from AnyConnect: The information is typically located in your profile xml files located here: /opt/cisco/anyconnect/profile/somethingsomething.xml In the xml file, you are looking for "<HostAddress>typicallyaDNSName.com</HostAddress>" entry.  These are your VPN endpoints that you would need to pass to openconnec...
Read more